# Close-to-Wall Tray Conditions – Convert to Tail Bearing

**Purpose**

When a tray or other ceiling feature is close to an outer bearing, the truss may need to be converted to a tail-bearing condition.

**Prerequisite**

An existing truss or layout with a tray or coffer close to an outer bearing.

**Steps**

Two examples illustrate this functionality.

![](/images/csdirector-cstruss/resources/images/ts-tray-coffer-close-to-outer-bearing.png)

**Example 1 (CS Truss Studio Profile Edits):**

1. Adjust truss span and edit truss TC and BC Profile (using the example above):


a. Change truss span from 24-0-0 to 21-6-8 (24’-0” – 2’-5 ½”) b. Edit TC Profile: c6 ha 1010 6 12 -6 e changes to c6 ha 10106 6 90608 -6 e c. Edit BC Profile: 0 20508 rv 1 0 70608 rv -1 0 e changes to 0 70608 rv -1 0 e d. Add 2’-5 ½” to existing overhang (total overhang length = 4’-5 ½")

![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-example2.png)

1. Add [Filler](/csdirector-cstruss/help-center/design-view/edit-joints/add-filler) to the underside of the top chord to account for the portion of truss that was removed.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** It is recommended that you use a board depth that allows the scarf cut to cover the width of the bearing.

![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-addfiller.png)

1. Trim, as required.


![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-trim.png)

1. Add blocking, as required (see [Add Board](/csdirector-cstruss/help-center/design-view/add-board)).


![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-addboard.png)

1. Edit [Bearings](/csdirector-cstruss/help-center/design-view/bearings/bearings) to reflect top chord bearing and location.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Currently, filler pieces are not structural. The plate above the bearing fastening the filler chord to the top chord must be reviewed by the sealing engineer.

**Example 2** **(CS Truss Studio Layout edits)**

![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-trimtruss-layout.png)

1. Trim trusses to left edge of tray.


![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-trimtruss2-layout.png)

1. [Trim top chord](/csdirector-cstruss/help-center/truss-studio-online-help/menus-toolbars/truss-operations-layout) ![](/images/csdirector-cstruss/resources/images/ts-trimbcicon.png) to left overhang


![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-trimtruss3-layout.png)

1. Select and [Review](/csdirector-cstruss/help-center/layout-view/review-trusses) truss.


![](/images/csdirector-cstruss/resources/images/ts-closetowalltray-exampletailebrg-498x205.png)

1. Follow steps 2-5 in Example 1 (above) to create the tail-bearing condition desired.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png)**Note**: [Scabs](/csdirector-cstruss/help-center/design-view/edit-joints/add-scabs) can be used to reinforce tail bearing trusses in bending, shear and deflection.

**Related Topics**