# Create Valley Rafters

**Purpose**

To generate non-structural, valley rafters

**Prerequisites**

A new or existing truss

**Steps**

![](/images/csdirector-cstruss/resources/images/video-icon.png)Watch video

To create valley rafters:

1. On the main Truss - Design workspace, click **Valley Rafters**.


![](/images/csdirector-cstruss/resources/images/ts-valleysetbutton-584x175.png)

The **Valley Rafters** window displays.

![](/images/csdirector-cstruss/resources/images/ts-valleysetdialog-470x297.png)

1. Define the settings for the valley set. As you enter settings, the information displays in the **Calculations** window.


**Valley settings**

Valley Span - enter span of the truss. For example, if you have a 30’ truss, you need a 30’ valley.

Valley Pitch - enter the pitch of the truss

Valley Heel - enter the heel height for the truss; the default value is zero. If you enter a value in this field and the Roof Heel field, Truss Studio determines the height difference between the two if the roof and valley have different heights.

![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/ts-valleyrafters-roofvsvalley-heels-460x291.png)

Valley wall height - use this setting in situations where the pop-out that the valley trusses originate from is not at the same wall height as the main span trusses. Note that you do not need to enter the actual height for the main roof and the valley pop-out. For example, if the valley pop-out is 1' higher than the main roof, you can enter 1-0-0.

![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/ts-valleypopout-338x219.jpg)

TC Butt - enter the top chord butt size

TC Size and Max Span - select top chord sizes from the drop down list for each span you enter. You can define three different sizes. For example, you might want a 2x4 top chord up to a 6' span, a 2x6 top chord up to a 10' span, and anything longer than a 10' span to be 2x8.

![](/images/csdirector-cstruss/resources/images/ts-valleysettcsizes-586x258.jpg)

OC Spacing - select a value for off-center spacing

Fill Direction - select a fill direction for the boards of either **Down Roof** or **Up Roof**.

1st Offset - define the first span

Exclude full span

PopOut Depth - use this setting in the situation where your walls jog out from the main wall of a room or for a bay window, for example.

Hip Pitch - enter a hip pitch

Hip to valley bevel - select a bevel from the drop down list; you can select None, Single, Double, or Double45. Double45 forces a 45 degree double bevel instead of using the corner rafter angle.

Roof Bevel - select a bevel type from the drop down list. **None** generates a square level cut, **Single** bevels the entire piece in one direction, and **Half** bevel, which goes to the center line of the member. **Double45** forces a 45-degree double bevel instead of using the roof angle.

**Roof settings**

Roof Pitch - enter the roof pitch

Roof Heel - enter the roof heel height; the default value is zero. If you enter a value in this field and the Valley Heel field, Truss Studio determines the height difference between the two if the roof and valley have different heights. See example above.

Roof Wall height - enter the roof wall height

Sheathing thickness - enter sheathing thickness

Sleeper A sleeper board provides a more secure nailing surface. size - select a size from the drop down list

Sleeper length - enter the sleeper board length

Count - select the number of sleeper boards from the drop down list

Ridge board size - this is the board that runs perpendicular to the TC rafters of the valley and the top of the valley rafters attach to. Enter a length to create a square cut ridge board.

Plys - select the number of plies

Ridge board Length - if you enter a specific length, a square cut is generated. If you leave this blank, the cut is based on the roof pitch.

Include ridge board(s)

1. Click **Build Valley Set Boards** when you finish entering settings.


A message displays asking if you want to clear your previous edits. If you click **OK**, the Valley Set boards are generated. A sample is shown below.

![](/images/csdirector-cstruss/resources/images/ts-valleysetsample.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) Note that when you use this command, analysis options are unavailable, but non-structural plate commands are available.

**Related Topics**

Valley