# Drag/Shear Loads on Base & Piggyback Trusses

**Purpose**

Adjust drag and shear load on base and piggyback trusses.

**Steps**

Follow these steps to create a piggyback truss with drag/shear loads.

![](/images/csdirector-cstruss/resources/images/ts-base-piggyback-drag-load.png)

1. Design a piggyback truss with a minimum of two bearings and the required drag load.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Notes:** The required drag load on the piggyback truss will be the same PLF drag load as the base truss, but will be a subset of the total drag load applied.

There are two ways to apply drag load:

- If you apply a PLF drag load, the amount will be the same for the piggyback as it is for the base truss.
- If you apply a total load drag load, for example, 5,000#, the amount of that drag load that applies to the piggyback truss is a smaller amount. Typically, that is calculated by dividing the span of the piggyback by the span of the base truss to get a ratio, then multiplying that ratio times the total drag load. As an example, if the base truss is 40' long, and the piggyback is 15' long, 15/40 = 0.375, so the drag load to apply is 0.375 times 5,000# (or whatever it is on the base truss) = 1875#, and not the full amount.


![](/images/csdirector-cstruss/resources/images/ts-piggybacktwobearings.png)

1. Record the downward and upward reactions at each bearing from the following load combinations:


- Dead + Drag; L>>R, Case 1
- Dead + Drag; L<<R, Case 1
- Dead + Drag; L>>R, Case 2
- Dead + Drag; L<<R, Case 2


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** These are located in the Applied Loads View. Select **Applications > Applied Loads View**. See [View Applied Loads](/csdirector-cstruss/help-center/design-view/loading/view-loads).

1. Open the base truss and apply the required drag load.
2. On the main workspace, navigate to **Component > Special** to open the **Special Loads** dialog.


![](/images/csdirector-cstruss/resources/images/ts-specialloaddialog.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Loads entered here are used *only* in user-created load combinations. See step 9, if necessary.

1. Enter the recorded down/up reactions from step #2 of the piggyback onto the TC of the base truss where the piggyback truss is supported. These loads are applied in two groups:


- Group A: ↓ ↑ (↓ reaction from left PB bearing, ↑ reaction from right PB bearing)
- Group B: ↑ ↓ ( ↑ reaction from left PB bearing, ↓ reaction from right PB bearing


![](/images/csdirector-cstruss/resources/images/ts-specialload-tcvertical.png)

![](/images/csdirector-cstruss/resources/images/ts-specialload-tcvertical-2-629x394.png)

1. Click **Show Group**, click <<new entry>> and click **Copy** to copy the load.
2. Adjust the direction(s) and magnitude(s) of the copied group, as needed.


![](/images/csdirector-cstruss/resources/images/ts-specialload-copyload-617x381.png)

![](/images/csdirector-cstruss/resources/images/ts-specialload-copyload-2-619x384.png)

![](/images/csdirector-cstruss/resources/images/ts-specialload-piggybackresult.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Use the [Export/Import Loads](/csdirector-cstruss/help-center/design-view/loading/export-and-import-loads) options to apply the same loads to multiple trusses.

1. Click **OK**.
2. On the main workspace, navigate to **Combinations** > **Load Combinations** **Editor** dialog.
3. Locate Dead + Drag; L>>R, Case 0 and select **Copy**, then **Edit**.
4. Adjust the **Name** as desired, select **Group B** with the L>>R reactions of the piggyback truss reactions, and set the factor to 1.00
5. Locate Dead + Drag; L<<R, Case 0 and select **Copy**, then **Edit**.
6. Adjust the **Name** as desired, select **Group A** with the L<<R reactions of the piggyback truss reactions, and set the factor to 1.00


![](/images/csdirector-cstruss/resources/images/ts-loadcombination-piggyback.png)

![](/images/csdirector-cstruss/resources/images/ts-loadcombination-piggyback-2.png)

1. Repeat for each Wind Case. In this example there are two, labeled Case1 and Case 2. Shown above is Case 1, repeat steps 5 through 13 for Case 2 using Group C and Group D.
2. Open the **Applied Loads View** and verify the new loads are applied at the correct locations, with accurate magnitudes and directions.


![](/images/csdirector-cstruss/resources/images/ts-piggybackappliedloads.png)

![](/images/csdirector-cstruss/resources/images/ts-piggybackappliedloads-2.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Use the [Export/Import Loads](/csdirector-cstruss/help-center/design-view/loading/export-and-import-loads) options to apply the same loads to multiple trusses.

**Related Topics**