# Add Filler

**Purpose**

Place non-structural framing (studs) at a regular interval below a truss; these members can be used for TC framing, BC framing, interior framing, and level returns. You can also use this feature to apply structural stacked chords.

**Steps**

To add filler:

1. Highlight the area of the truss where you want to add filler.
2. In the Design workspace, click **Filler**. In the Layout workspace, select **Filler** from the **Truss Modifications** menu.


![](/images/csdirector-cstruss/resources/images/filler-button-363x219-537x171.png)  The **Filler** dialog displays.  ![](/images/csdirector-cstruss/resources/images/filler-dialog-465x272-472x313.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png)**Note:** If no filler entries exist, the window displays preset values. If filler entries exist, the values for the first filler in the list displays.

Filler options include the following:

**Location**

See the illustration below for more information.

**X-Begin** - define the filler start location by selecting a dimension in the drop-down list or by entering a dimension in ffiiss. The start location is measured from the left end of the truss along the horizontal axis.

**X-End** - define the filler end location by selecting a dimension in the drop-down list or by entering a dimension in ffiiss. The end location is measured from the left end of the truss along the horizontal axis.

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** X-End can be to the left of X-Begin, which then places a filler from right-to-left.

**Y-Offset** - define the height of the filler by selecting a dimension in the drop-down list or by entering a dimension in ffiiss. The height is measured from the selection in Y-Offset at X_Begin From...

**Y-Offset at X_Begin From...** - click the button next one of the following options to define how the Y-Offset is measured.

(0,0) Closest Bearing Top Edge TC Bot Edge TC Top Edge B Bot Edge BC

![](/images/csdirector-cstruss/resources/images/filler-options-493x217.png)

![](/images/csdirector-cstruss/transparent.gif)Joint Control

If this option is off, Truss Studio attempts to plate the joint with one plate. To use two plates (treat as two joints), turn this option on.

Here are two examples of this setting.

Joint Control is turned off:

![](/images/csdirector-cstruss/resources/images/joint-control-off-478x190.png)

Joint Control is turned on:

![](/images/csdirector-cstruss/resources/images/joint-control-on-481x206.png)

![](/images/csdirector-cstruss/transparent.gif)**Chord Info**

**Extend Existing Chord** - make the filler chord part of the original chord instead of creating a break.

**Create New Chord(s)** - filler chord is not an extension of the original chord; it is a separate piece of board.

**Stacked TC** - check to add a structural stacked top chord

**Stacked BC** - check to add a structural stacked bottom chord

Note that you can use both stacked chord options simultaneously. When either option is selected, all of the Filler options are disabled, except for X-Begin, X-End, and Size. Truss Studio auto-trims any stacked members to the nearest webbing left of the Begin location, and right of the End location.

![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/ts-filler-stackedstructchords-450x212.png)

**Size** - select size of filler chord from drop-down list.

**Profile** - pitch1 setback1 pitch2 setback2 - define the pitch of the filler chord(s). For more than one pitch, user would add first pitch and distance, second pitch and distance, etc.

![](/images/csdirector-cstruss/transparent.gif)Trim Options

**Left/ Right**

- No Trim - overlapping chords are not trimmed. If this option is selected, the specified location for the X-begin or X-end of the member is used to determine the end point of the stacked member. The end cut of a No Trim member is always plumb.
- Trim to Closest Member - overlapping chords are trimmed. If this option is selected, but there is no web member on that end of the stack to trim to, the specified location is used to determine the end point. Therefore, an untrimmed stacked chord added to a sloped member will always have a vertical (plumb) cut. Square cuts will happen automatically only if the pitch is zero. However, trim lines can be used to modify, if needed. Setting a workline perpendicular to the chord at the point where the end of the stacked chord touches the regular chord and then trimming to that line provides the same length board as input.


Trim to member example

![](/images/csdirector-cstruss/resources/images/ts-fillertrimclosestmemb-886x478.png)

No Trim example

![](/images/csdirector-cstruss/resources/images/ts-fillernotrim-883x538.png)

![](/images/csdirector-cstruss/transparent.gif)**Studding**

**None** - select for no studding under or over filler chords

**Add Studs Where Permitted** - select to add studs based on values in the studding options

**Size** - select size of filler stud from the drop-down list

**Spacing** - select stud spacing from the drop-down list or enter a dimension in ffiiss format

**Min Length** - define minimum length of filler studs to add by selecting from the drop-down list or entering a dimension in ffiiss. Studs shorter than the Min Length dimension are removed.

**Direction** - define direction of stud placement by selecting Left to Right, Right to Left, Ends In or Peak Out from drop-down list.

![](/images/csdirector-cstruss/transparent.gif)See studding examples

![](/images/csdirector-cstruss/resources/images/ts-filler-studdingexamples.png)

**V Placement Control** - define vertical stud placement by selecting Auto, Above, or Below from the drop-down list. Generally, Truss Studio will calculate placement automatically; however, you must sometimes specify placement, as shown in the examples below.

**H Placement Control** - define horizontal stud placement by selecting Left, Centered, or Right from the drop-down list.

![](/images/csdirector-cstruss/transparent.gif)Examples

Filler set to **Above**:

![](/images/csdirector-cstruss/resources/images/filler-above-464x202.png)

Filler set to **Below**:

![](/images/csdirector-cstruss/resources/images/filler-below-417x169.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png)**Note:** The filler chord is also flipped in the direction of placement.

**Add Vert Over Brg** - Add a bearing below a vertical - by moving the bearing graphic from under the bottom chord to under the filler. (The vertical may or may not exist in the filler already.) Note that the filler is still non-structural and in the analysis, the bearing is considered to be under the sloped bottom chord.

• When this option is checked, Truss Studio automatically places any bearing within the filler area under the filler chord, and will not allow you to move it.

• When this option is unchecked, Truss Studio allows you to place any bearing within the filler area at any location, TC, web, BC, or filler, via the Bearings dialog.

You can turn this option on/off on a case-by-case basis (by using the Add Vert Over Brg option) or completely disable the setting by selecting False in the Env Data settings for Dialogs > Cosmetic Filler.

![](/images/csdirector-cstruss/resources/images/ts-addvertoverbearing-envdata-359x179.jpg)

![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/unchecked-vert-under-bearing-290x217.png)

![](/images/csdirector-cstruss/resources/images/checked-vert-bearing-299x219.png)

**Setbacks** - hold back the last stud from either end of the chord (often used for plant shelves).

Select from the drop-down list or enter a dimension in ffiiss for left, right, or both.

![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/filler-holdback-511x172.png)

1. To add filler chords and studs, click **<<new entry>>** and define the values for the new filler in the upper part of the window. Click **OK**.


![](/images/csdirector-cstruss/resources/images/new-entry-filler-467x273.png)

The filler displays in the truss.

1. To add multiple fillers without leaving the window, click **Save** after each entry. Click **Apply** to apply all settings to the current truss without closing the window.


![](/images/csdirector-cstruss/transparent.gif)Examples of Filler in Trusses

![](/images/csdirector-cstruss/resources/images/polyfill-transition-gable-629x382.jpg)

![](/images/csdirector-cstruss/resources/images/polyfill-dutch-gable-625x375.jpg)

![](/images/csdirector-cstruss/resources/images/polyfill-letin-gable-626x372.jpg)