# End Conditions/Descriptions ![](/images/csdirector-cstruss/resources/images/ts-enddescimage-58x58.png)

**Purpose**

Define the end conditions of roof and floor trusses. Sliders, wedges, and various end conditions can be defined, modified, or deleted.

**Steps**

![](/images/csdirector-cstruss/resources/images/video-icon-35x36.png) Watch Mansard Truss video

![](/images/csdirector-cstruss/resources/images/video-icon-35x36.png) Watch No Reinforcement video

![](/images/csdirector-cstruss/resources/images/video-icon-35x36.png) Watch Block and Post/Parapet video

![](/images/csdirector-cstruss/resources/images/video-icon-35x36.png) Watch TC/BC Ledger Pocket video

![](/images/csdirector-cstruss/resources/images/video-icon-35x36.png) Watch Double Ribbon Block video

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** End descriptions can be applied to individual trusses in Design view. They can also be applied to one or more trusses simultaneously in Layout view.

To define end conditions:

1. Click **Left End Desc** or **Right End Desc** to open the appropriate window. From the Layout view, access these options on the **Truss Modifications** menu or click ![](/images/csdirector-cstruss/resources/images/ts-enddescbuttons.png).


![](/images/csdirector-cstruss/resources/images/ts-leftenddescdialog.png)

1. Complete the **End Description** options. The Left and Right End Description windows contain the same options.


The **Use automatic settings** option lets you automatically create a truss profile around the end conditions. If this is unchecked, you can define the profile manually.

**End Detail Options**

| **Number** | **Description** | **Example** |
|  --- | --- | --- |
| 1 | Girder Cut | ![](/images/csdirector-cstruss/resources/images/ts-girdertrussexample-608x219.png) |
| 1A | Ripped Tail on Overhang | ![](/images/csdirector-cstruss/resources/images/ts-rippedtailoh-619x215.png) |
| 2 | Extra member slider | ![](/images/csdirector-cstruss/resources/images/ts-endcondition-extraslider-628x272.png) |
| 3 | BC Cut back | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-bccutback.png) |
| 4
 | TC Ledger Pocket
BC Ledger Pocket
You can also apply a 2x4 ledger pocket with mitered chord-to-web interface on top chord or bottom chord.
 | ![](/images/csdirector-cstruss/resources/images/ts-endcondition-ledgerpockets-494x256.png)
![](/images/csdirector-cstruss/resources/images/ts-endcondition-ledgerpocket-2x4-505x269.png)
 |
| 4a.
 | Ledger Pocket & Parapet
 | Apply both a bottom chord ledger pocket and parapet extension in End Detail Options for the same truss end.
![](/images/csdirector-cstruss/resources/images/ts-ledgerpocket-parapet-endconds.png)
 |
| 5 | Mansard | ![](/images/csdirector-cstruss/resources/images/ts-endcondition-mansard-1023x214.png) |
| 6 | Fire cut | ![](/images/csdirector-cstruss/resources/images/ts-endcondition-firecut.png) |
| 7 | Setback | ![](/images/csdirector-cstruss/resources/images/ts-setback-tcholdback-473x257.png) |
| 8
 | Bearing Block
TC Ledger Pocket
 | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-bearingblock-538x381.png)
![](/images/csdirector-cstruss/resources/images/ts-tcledgerpocket-andbearingblock-551x924.png)
 |
| 9 | Bearing Block with BC Cutback | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-bbwithbccutback-589x861.png) |
| 10 | Ribbon Post | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-ribbonpost-562x412.png) |
| 10a. | Double Ribbon | ![](/images/csdirector-cstruss/resources/images/ts-wx2-bc-brg-dblendvert-ribbonnotch.png) |
| 11 | Adjust End Vertical (Add Parapet and Drop Leg) | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-mansardpost-583x430.png) |
| 12 | Wedge | ![](/images/csdirector-cstruss/resources/images/ts-2xw-max-wedge-size-628x216.png) |
| 13 | TC Half Panel Slider | ![](/images/csdirector-cstruss/resources/images/ts-tc-halfpanelslider-638x227.png) |
| 14 | BC Full Panel Slider | ![](/images/csdirector-cstruss/resources/images/ts-enddesc-bcfullpanelslide-641x229.png) |
| 15 | Strut | ![](/images/csdirector-cstruss/resources/images/ts-strutendcondition-648x223.png) |


- Use automatic settings - When checked, all user-controls are disabled and presets defined in EnvData are used. When unchecked, selected options are enabled.
- Girder Cut - change a standard heel to a girder cut (See 1)
- Ripped Tail - create ripped tail on overhang (See 1A). See [Ripped Tail Cut](/csdirector-cstruss/help-center/design-view/rippedtailcut) for more information.
- TC Brg/Gap - change to a Top Chord bearing condition. Also, a gap dimension between the TC bearing and the first vertical can be added. (See 2 & 3). Select the gap dimension from the Dimension drop-down list or enter it manually. The gap dimension is measured horizontally from the inside of the bearing to the outside of the end vertical.
- BC Cut-back - hold back the bottom chord. If this option is selected, the end vertical is removed. (See 3). Select the cut-back dimension from the Dimension drop down list, or enter it manually. The cut-back dimension is measured horizontally from the outside of the bearing to the end of the bottom chord.
- TC/BC Ledger Pocket - specify the width of the pocket. Note that the pocket height matches the bottom chord size; the bearing is changed to a "beam" bearing to match the specified size of the pocket, and will be moved up into the pocket. Plating routines check for this end condition and move/orient the plate accordingly. See [Create Ledger Pocket](/csdirector-cstruss/help-center/design-view/create-ledger-pocket). Note that you can apply both a bottom chord ledger pocket and parapet extension in End Description for the same truss end. (See 4a.)
- Mansard - click to create a mansard-style, mono truss.
- Trimmable End - check this to use trimmable ends for both Trim Fit and EverTrim products, based on licensing and inventory from CS Director.
- TC Holdback - select Fire Cut or Setback from the drop down list. For 2xW trusses, Fire Cut is the only option available.
- A fire cut allows you to change a standard floor truss end to a fire cut end. (See 6). Select the fire cut dimension from the Dimension drop down list or enter it manually. The fire cut dimension is measured horizontally from the end of the bottom chord to the end of the top chord.
- For Setback, see 7 above.
- Define the end condition by selecting one of the following:
- X Dist lets you specify the X amount in from the end of the truss to the end point of the TC at the top edge of the TC.
- Pitch lets you specify the pitch of the end web.
- Angle lets you specify the angle of the end web.
- Web Size - select end web dimensions from the drop down list


![](/images/csdirector-cstruss/resources/images/ts-tcholdback.png)

- End Jack - define a truss as an end jack. When this option is enabled, Truss Studio uses the settings in Layout > Hipset > Jack TC/BC Bearing Type to determine the type of new bearings created by the use of the TC/BC Supported check boxes. These check boxes create end bearings for TC, BC, or both, independent of whether the End Vertical is removed.


![](/images/csdirector-cstruss/resources/images/ts-endvertbearingtype.png)

- When End Jack is selected, EnvData settings will be used to determine the panel lengths for the jacks. See [Panel Lengths 2xW](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/panel-lengths-2xw-settings) for more information.
- Remove End Vert - if checked, the end vertical is removed.
- TC Supported - if checked, a hanger is added to the TC on the high end of the end jack. If the end vertical is removed, the TC should be supported whether or not this is checked.
- BC Supported - If checked, the BC has a bearing under it.


#### **Extra Member Options**

![](/images/csdirector-cstruss/resources/images/ts-enddesc-extramembers.png)

Wedge - add a wedge to the heels of trusses that do not have a separation between the TC and BC ends. (See 12)

Size - select the size from the drop down list, or enter it manually.

Slider - add a slider to the heels of trusses that have a separation between the TC and BC ends. (See figure 13 & 14)

- TC/BC - select a TC, or BC slider.
- Size - select the size of the slider from the drop down list, or enter it manually.
- Length - select the length of the slider from the drop-down list, or enter it manually.


Strut - this option becomes available when the step size in the profile is greater than the chord size. (See Figure 15).

End Vert - add an end vertical.

No Reinforcement - specify this option if you do not want to use a wedge or slider.

#### **Block and Post options**

- None - No block or post is added (default)
- Brg Block - add a bearing block to the end of a roof or floor truss. It can be used in combination with TC Brg and BC Cut-back. (See 8 & 9).You can also apply both Top Chord Ledger and Bearing Blocks concurrently.
- Size - select the size of the bearing block from the drop down list, or enter it manually. This setting applies to all the Block and Post options except for “None.”
- Ribbon Post/Adjust End Vertical (Add Parapet and Drop Leg) - add a top and/or bottom chord ribbon post or mansard post. Ribbon posts are created using positive y entries and mansard posts are created using negative y entries. (See 10 & 11).
- Double Ribbon - create two ribbon blocks at different lengths/depths on a floor truss end condition (double, terrace) (See 10a).
- Adjust End Vertical - create a parapet or drop leg condition. A positive value adjusts the end vertical into the truss while a negative value extends the end vertical outside of the truss based on the user-specified Y-measurements.
- Top Y-Measure (gap) - Gap for Ribbon Post/Mansard Post measured vertically from the top edge of the Top Chord to the top edge of the post. (See 10 & 11).
- Bottom Y-Measure (gap) - Gap for Brg Block or Ribbon Post/Mansard Post measured vertically from the bottom edge of the Bottom Chord to the bottom edge of the bearing block or post.
  - Use these settings to specify an overall height in the Y-measure for either the TC or BC location of the block; use the @ symbol to signify absolute Y-dimension.


![](/images/csdirector-cstruss/resources/images/ts-adjendverticaloptions-517x199.png)

![](/images/csdirector-cstruss/transparent.gif)Example

![](/images/csdirector-cstruss/resources/images/ts-enddescriptionatsign-591x357.png)

Specify parapet extensions using End Descriptions in Layout and Design.

![](/images/csdirector-cstruss/transparent.gif)Example

![](/images/csdirector-cstruss/resources/images/ts-parapet-condition-4794-580x361.png)

**Related Topics**

[End Conditions 2xW Settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/end-conditions-2xw-settings)

[End Conditions Wx2 Settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/end-conditions-wx2-settings)