# Create Overhangs

**Purpose**

Create overhangs that extend beyond the outside bearing of a truss.

**Steps**

To create overhangs:

1. Click ![](/images/csdirector-cstruss/resources/images/ts-overhangbutton.png) next to **Overhangs** to open the **Left overhangs** or **Right overhangs** window.


![](/images/csdirector-cstruss/resources/images/ts-overhangbuttons-333x210.png)

The Overhang Left/Right dialog displays with the current overhang lengths; the BC length defaults to zero. Both the Overhang Right and and Left windows contain the same settings.

1. Define the following options:


OH Length - select the overhang length for both top and bottom chords

How Measured - select the method for measuring the overhang from the drop down list

- OutPnt - Horizontal measurement from the longest point on the overhang to the heel.
- InPnt - Horizontal measurement from the shortest point on the overhang to the heel
- Rake - Measurement along the top side of the overhang to the heel


End Cuts - select the type of cut to use at the end of the overhang from the drop down list. Examples of each type are shown in the illustration below.

![](/images/csdirector-cstruss/resources/images/ts-leftenddesc-fascia-new.png)

When Seat or Fascia end cuts are selected, additional fields for Seat Angle, Cut Length, and Fascia Angle display on the dialog.

![](/images/csdirector-cstruss/resources/images/ts-overhang-seatcut.png)

![](/images/csdirector-cstruss/resources/images/ts-fasciaoverhangs.png)

- Plumb cut - Single cut, perpendicular to the x-axis. (See 2).
- Square cut - Single cut, perpendicular to the board. (See 2). Beginning in 2025.1 the overhang length is based on how the overhang is measured (dimensioning matches the chosen option of outside/inside on the Overhang dialog). This means that the measurements displayed on a report match the expected result, ensuring that trusses are built correctly with no misinterpretation of the data.
- Angle cut- Single cut which is at the angle set in the Angle 1 field. (See 4). When you select this option, you can choose an angle from the Angle dropdown list.
- Seat cut (formerly DblCut) - Double cuts which are at the angles set in the Angle 1 and Angle 2 fields. (See 3).
- Fascia - Fascia cuts on ends (See 5). If you select Fascia, the dimension to enter is the vertical or fascia cut. Both the seat and/or the fascia cut can be at an angle; these cuts do not need to be horizontal and vertical.


![](/images/csdirector-cstruss/resources/images/ts-overhangexamples-2024.-977x382.png)

![](/images/csdirector-cstruss/transparent.gif)Fascia cut example

![](/images/csdirector-cstruss/resources/images/ts-fasciaoverhangoption-new-800x759.png)

Dimension - enabled if **Seat** (formerly DblCut) is selected. You can select the length of Angle 1 on a seat cut end from the drop down list, or enter it manually. (See 3).

Angle 1 - enabled if **Angle** or **Seat** is selected. You can select the angle for an angle-cut end, or the lower angle for a seat cut end from the drop down list, or enter it manually.

Angle 2 - enabled if **Seat** is selected. You can select the upper angle for a seat cut end from the drop down list, or enter it manually. (See 4).

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png)**Note:** Angles are measured in degrees from a plumb line through the reference point on the end of the overhang. A positive angle is a cut toward the truss; a negative angle is a cut away from the truss.

1. Click **OK** to save your changes.


The **Overhang** field reflects information that you defined in the **Overhangs** dialog.

![](/images/csdirector-cstruss/resources/images/ts-overhangresults-289x33.png)

Beginning in 2025.1, Currently when a square cut overhang is measured from the outside point the overhang dimension that is displayed pulls from the inside point. So, on a 12/12 pitch truss the user inputs an overhang length of 2-0-0 but the resulting overhang dimension displays as 1-9-8, which is the correct dimension to the inside point on an overhang that is 2-0-0 to the outside point but the user wants to see an overhang length based on how the overhang is measured, meaning they want to see a dimension of 2-0-0.

#### Create New Overhangs on Stubbed Truss

When a truss is stubbed, the existing overhangs are deleted. The New OH functiona lets you add overhangs to a stubbed truss.

![](/images/csdirector-cstruss/resources/images/ts-overhangstubtruss.png)

In this case, the left end was stubbed, removing t overhang.

Follow these steps to add a new overhang:

1. In the **New OH** box, enter the length of the overhang or click ![](/images/csdirector-cstruss/resources/images/ts-overhangbutton.png) next to **New OH** and enter the information in the window. This is the same process as described above for creating overhangs.


![](/images/csdirector-cstruss/resources/images/ts-newoh-stub1-1062x608.png)

![](/images/csdirector-cstruss/transparent.gif)![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Interior overhangs are structural and have appropriate loads applied. An interior overhang includes top chord overhangs that are directly over another top chord member.

![](/images/csdirector-cstruss/resources/images/ts-interioroverhangs.png)

**Related Topics**

[Walls and Planes settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/walls-and-planes-settings)

[Create Overhang for Exposed Porch](/csdirector-cstruss/help-center/design-view/createoverhangexposedporch)