# Plate Handling File Overview

**Purpose**

The plate handling file contains the initial settings for starting plates sizes for many joint types, based on truss span and chord size. The plating routine in the truss design checks this file first to see what plate to start with at each joint when analyzing the truss. You can edit the plate handling file to meet your individual requirements.

**Steps**

1. Select **Environment > Load Plates Handling** and navigate to the Plates Handling file you want to open.
2. Click **Open**.
3. Select **Environment > Edit Plates Handling** to open the selected file.


The **Plates Handling** window opens.

![](/images/csdirector-cstruss/resources/images/ts-platehandlingfilenew-805x411.png)

Factors and Minimums for Handling

Zone Factors - At the top of the window, you can edit the values in the Zone field. Zone 1, 2, 3 on the left are editable. Zone 1 and 2 on the right are for symmetry, and are not editable. Zone Factors let you increase plate sizes in certain zones, using a multiplier. Each zone is 20% of the truss span.

![](/images/csdirector-cstruss/resources/images/ts-zone-factors.png)

Minimum Area and Minimum Bite - enter the appropriate values into the Minimum Area and/or Minimum Bite fields

![](/images/csdirector-cstruss/transparent.gif)Notes about Minimum Bite

- 30’ is considered a “standard” span
- 2x4 has settings for smaller spans (6’) so that you can have separate controls for jack trusses in particular
- The application switches between the settings. so for example, a 20’ span would interpolate between the 6’ setting and the 30’ setting, for 2x4, if those factors are different.
- The 2x2 and 2x12 is an additional “size” factor that can be used so that larger lumber gets a larger factor – the program interpolates between the 2x2 and 2x12 setting based on what the actual lumbersize is.
- The program interpolates Interpolate means that the actual value used is determined (by ratio) depending how close the actual number is to either of the settings. This provides a smooth transition between numbers so that plates don’t have a “jump” in the required area or bite because they are just less or just above the test span limit.  between the 30’ setting and the 80’ setting based on the actual truss span. A 2x4 truss doesn’t generally span out that far, but in this case the program is looking at end-to-endspan, so it could be a truss that has multiple interior bearings that make it work structurally. The 80’ setting affects any span larger than 30’.


Joint Type

1. Select the type of joint you want to set values for from the **Joint Type** list.


| Joint Type | Joint Type example | Additional notes |
|  --- | --- | --- |
| Non-break, 1-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-joint-nonbreak-1-web-315x305.png) | Sample Truss 1 below includes this joint type. |
| Non-break, 2-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-joint-nonbreak-2-web-329x319.png) | Sample Truss 1 below includes this joint type. |
| Non-break, 3-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-joint-nonbreak-3-web-337x328.png) | Sample Truss 1 below includes this joint type. |
| Non-break, >=4-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-joint-nonbreak-4-web-385x368.png) | Sample Truss 2 below includes this joint type. |
| Splice, inner-panel | ![](/images/csdirector-cstruss/resources/images/ts-plating-joint-splice-innerpanel-389x389.png) | Sample Truss 1 below includes this joint type. |
| Splice, at panel-point | ![](/images/csdirector-cstruss/resources/images/ts-plating-splicepanelpoint-384x384.png) | Sample Truss 1 below includes this joint type. |
| Break, no webs | ![](/images/csdirector-cstruss/resources/images/ts-plating-breaknowebs-434x434.png) | Sample Truss 2 below includes this joint type. |
| Break, Symm Concave (Peak) | ![](/images/csdirector-cstruss/resources/images/ts-platingbreak-symmconcave-429x429.png) | Sample Truss 1 below includes this joint type. |
| Break, Asymm Concave | ![](/images/csdirector-cstruss/resources/images/ts-platingbreak-asymmconcave-431x424.png) | Sample Truss 3 below includes this joint type. |
| Break, Hip | ![](/images/csdirector-cstruss/resources/images/ts-plating-breakhip.-437x437.png) | Sample Truss 4 below includes this joint type. |
| Box, Calif Hip; other | ![](/images/csdirector-cstruss/resources/images/ts-plating-boxcalhip-644x307.png) | Sample Truss 5 below includes this joint type. |
| Web Pass-thru | ![](/images/csdirector-cstruss/resources/images/ts-platingwebpassthru.png) | Sample Truss 2 below includes this joint type. |
| Web Pass-Thru (Parapet) | ![](/images/csdirector-cstruss/resources/images/ts-jointtype-passthru-1326x854.png) |  |
| Break, Convex | ![](/images/csdirector-cstruss/resources/images/ts-plating-breakconvex.png) | Sample Truss 6 below includes this joint type. |
| Vertical step, no K-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-vertstep-nokweb.png) | Sample Truss 2 below includes this joint type. |
| Vertical step, possible K-web | ![](/images/csdirector-cstruss/resources/images/ts-plating-vert-step-possk-web.png) | Sample Truss 2 below includes this joint type. |
| Wx2, Wide face | ![](/images/csdirector-cstruss/resources/images/ts-wx2-wide-face-768x374.png) |  |
| Wx2, 1-web | ![](/images/csdirector-cstruss/resources/images/ts-wx2-1-web.png) | Sample Truss 7 below includes this joint type. |
| Wx2, 2-web | ![](/images/csdirector-cstruss/resources/images/ts-wx2-2-web.png) | Sample Truss 7 below includes this joint type. |
| Wx2, 3-web | ![](/images/csdirector-cstruss/resources/images/ts-wx2-3-web.png) | Sample Truss 7 below includes this joint type. |
| Gable, non-break | ![](/images/csdirector-cstruss/resources/images/ts-plating-gablenonbreak.png) | Sample Truss 8 below includes this joint type. |
| Gable, break | ![](/images/csdirector-cstruss/resources/images/ts-plating-gablebreak.png) | Sample Truss 8 below includes this joint type. |
| Heel, no extra members | ![](/images/csdirector-cstruss/resources/images/ts-plating-heelnoxtramembers.png) |  |
| Heel, with wedge | ![](/images/csdirector-cstruss/resources/images/ts-plating-heelwedge.png) |  |
| Heel, with slider | ![](/images/csdirector-cstruss/resources/images/ts-plating-heelslider.png) |  |
| TC Bearing, no bearing block | ![](/images/csdirector-cstruss/resources/images/ts-plating-tcbearing-nobrgblk.png) |  |
| TC Bearing, with bearing block | ![](/images/csdirector-cstruss/resources/images/ts-plating-tcbearing-withbrgblk.png) |  |
| Non-structural splice, no webs | ![](/images/csdirector-cstruss/resources/images/ts-plating-nssplice-nowebs.png) | Sample Truss 9 below includes this joint type. |
| Non-structural splice, with webs | ![](/images/csdirector-cstruss/resources/images/ts-plating-nssplice-withwebs.png) | Sample Truss 9 below includes this joint type. |
| Non-structural splice, 1-web non-break | ![](/images/csdirector-cstruss/resources/images/ts-plating-onewebnonbreak.png) | Sample Truss 9 below includes this joint type. |
| Non-structural splice, 2-web, non-break | ![](/images/csdirector-cstruss/resources/images/ts-plating-twowebnonbreak.png) | Sample Truss 9 below includes this joint type. |
| Non-structural splice, >=3-web non-break | ![](/images/csdirector-cstruss/resources/images/ts-plating-threewebnonbreak.png) | Sample Truss 9 below includes this joint type. |
| Pass-thru structural, 1 web per side | ![](/images/csdirector-cstruss/resources/images/ts-plating-passthrustruct-onewebperside.png) | Sample Truss 10 below includes this joint type. |
| Pass-thru structural, >=2 webs per side | ![](/images/csdirector-cstruss/resources/images/ts-plating-.passthrustruct-2webperside.png) | Sample Truss 10 below includes this joint type. |
| Pass-thru non-structural, 1-web per side | ![](/images/csdirector-cstruss/resources/images/ts-passthruns-onewebperside.png) | Sample Truss 11 below includes this joint type. |
| Pass-thru non- structural, >=2- webs per side | ![](/images/csdirector-cstruss/resources/images/ts-passthruns-twowebperside.png) | Sample Truss 11 below includes this joint type. |


Examples

![](/images/csdirector-cstruss/transparent.gif)Example Truss 1

![](/images/csdirector-cstruss/resources/images/ts-jointplating-truss-example-1.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 2

![](/images/csdirector-cstruss/resources/images/ts-jointplating-truss-example-2-1102x650.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 3

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex3-912x533.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 4

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex4-1055x504.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 5

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex5.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 6

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex6-1182x551.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 7

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex7-1121x468.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 8

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex8-1045x608.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 9

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex9-1172x585.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 10

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex10.png)

![](/images/csdirector-cstruss/transparent.gif)Example Truss 11

![](/images/csdirector-cstruss/resources/images/ts-plating-trussex11.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) Note that **Span <** in the first column is less than the span indicated. This means that the 30’ row applies to anything between 20’ and 30’, but a 30’-6” span will use the 40’ information.

![](/images/csdirector-cstruss/resources/images/ts-jointtype-platingfile.png)

The minimum plate size is indicated in two rows for each span; the first row “W” is the Width of the minimum plate, and the second row “L” is the Length of the minimum plate.

The actual plate size used is based on the plate inventory, not this file; the plate selected may be larger than these settings. The columns are based on the TC or BC size, not the web size.

A grid of values displays on the right side of the window. You can increase the minimum plate size based upon the type of joint, the depth of the lumber and the span of the truss.

1. Click a value in the grid to change it.
2. Click **Save** to save your changes. Note that when you save changes to the Plates Handling file the changes are saved only for the project you are currently working in. If you want those changes applied to your default template in Director, or to other projects, you must copy that file to those project locations.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Plating for undefined joint types can be controlled using the 2” column.

**Related Topics**

[Managing Plate Handling File Presets](/csdirector-cstruss/help-center/design-view/plate-handling/managing-plate-handling-file-presets)