# Use Special Loads for Steeples & Cupolas

**Purpose**

The following topic provides an example of how to create and use Special Loads to apply loading to a truss that will carry a steeple/cupola. Note that the loads discussed below are from a specific example, and the numbers were provided by the steeple manufacturer; it is the responsibility of the Building Designer or the EOR to determine and specify what the connection load requirements are.

In most cases, the issue is not the dead load of the steeple (which should be applied as regular user point loads (dead only)), but how to apply the loads for the four wind directions:

- Left-to-Right
- Right-to-Left
- Perp-to-truss-Up
- Perp-to-truss-Down


This is a picture of the Finite Element Analysis that pertains to the example below:

![](/images/csdirector-cstruss/resources/images/ts-steeplesample-627x518.png)

Reaction information is shown below.

![](/images/csdirector-cstruss/resources/images/ts-steepletable.jpg)

- The highlighted number in the **FX** column is the wind shear; it is recommended to round that up to 1,000#.
- The **FY** column displays both the Uplift and the Downward maximums from wind, plus the weight. Up = 2250#, Down = 2882#, Dead (not from wind) = 316#
- These numbers are for each of the 4 attachment points (4 nodes, as shown in the above analysis results). It is recommended to use the maximum of all four corners as indicated above.


**Steps**

1. In the Point Load dialog, add the dead load for the point loads, as well as the appropriate locations. There are two locations on each truss; an example is shown below.


![](/images/csdirector-cstruss/resources/images/ts-pointloaddialog-steeple.jpg)

1. Create “Special” point loads for the other values; they will be at the **same** locations as in Step 1. Since the Dead Load is already applied, you will need to account for that in the Up and Down loads you enter:  Since these two are the same value, but in opposite directions, you can simplify the entry by creating the Special loads once, then using the negative factor to switch the direction. See Step 4 for additional information. Shear = 1000# at each location – since this is a horizontal load, the dead load has no effect on it.


- Uplift = 2250 + 316 = 2566 # - It is recommended to round that up to 2600#.
- Down = 2882 – 316 = 2566# - It is recommended to round that up to 2600#.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Each entry below is in a different group since you want to control each separately from the others. therefore, it is recommended to use the following 4 entries, *using your correct X locations*; the values provided below are only an example.

![](/images/csdirector-cstruss/resources/images/ts-steepleex-1-675x405.jpg)

![](/images/csdirector-cstruss/resources/images/ts-steepleex-2-678x408.jpg)

![](/images/csdirector-cstruss/resources/images/ts-steepleex-3-684x411.jpg)

![](/images/csdirector-cstruss/resources/images/ts-steepleex-4-689x413.jpg)

1. Click **OK** twice to save your changes. Note that if you have more than one truss to put these on, you can use the **Export** and **Import** buttons to save the entries out to a file, then load them up on the next truss; in this way, you only need to change the X-locations (if they are different) for the current truss you are working on. You can also do this with the Load Combinations, below.
2. Open the **Load Combination Editor** and do the following:
3. Locate the **MWFRS L>>R Case 1** and highlight it in the list. Click **Copy** and then **Edit**.
4. Change the name to **MWFRS L>>R + Steeple Loads** (or something similar), and do the following (Up, Down, Right, Right):
5. Keep the **Load Duration** and settings for **Dead Load**; **Factored** and **Wind** – MWFRS as is.
6. Select the Group A load and use a negative -1.0 factor.
7. Select the Group B load and use a positive 1.0 factor, (use the drop down arrow at the right end of the Special Loads to select group B, C, D).
8. Select the Group C load and use a positive 1.0 factor.
9. Select the Group D load and use a positive 1.0 factor.


![](/images/csdirector-cstruss/resources/images/ts-steepleloadingex.jpg)

c. Click **OK** to save the case.

d. Note that load case will still be highlighted in the **Load Combination** **Editor** window. Click **Copy**, then **Edit**.

e. Change the name to **MWFRS R>>L + Steeple Loads**, and do the following (Down, Up, Left, Left):

1. Change the **Wind** load case by setting the **MWFRS L>>R Case 1** factor to 0.00, then select the **MWFRS R>>L Case 1** and set the factor to 1.00.
2. Change the Group A factor to 1.0.
3. Change the Group B factor to -1.0.
4. Change the Group C factor to -1.0.
5. Change the Group D factor to -1.0.


f. Click **OK** to save the case.

g. With the load case highlighted, click **Copy**, then **Edit**.

h. Change the name to **MWFRS Perp + Steeple Loads**, and do the following (Down, Down, zero, zero)

1. Change the Wind load case by setting the MWFRS R>>L Case 1 factor to 0.00. Select the **MWFRS, Perpendicular to Ridge** case and set the factor to 1.00.
2. Verify that the Group A factor is 1.0.
3. Change the Group B factor to 1.0.
4. Change the Group C factor to 0.0.
5. Change the Group D factor to 0.0.


i. Click **OK** to save the case.

j. With the load case highlighted, click **Copy**, then **Edit**.

k. Change the name to **MWRFS Perp – Steeple Loads**, and do the following (Up, Up, zero, zero):

1. Keep the same MWFRS Perp to Ridge case set to 1.0.
2. Change the Group A factor to -1.0.
3. Change the Group B factor to -1.0.
4. Verify the Group C factor is 0.0.
5. Verify the Group D factor is 0.0.


l. Click **OK** to save the case.

m. In **Load Combinations**, you should see something like the below example (four user load combinations created by the above actions):

![](/images/csdirector-cstruss/resources/images/ts-steeplecompletedloadcombos.jpg)

1. Use the **Export** and **Import** buttons to save the load cases to a file, then import them to another truss; this ensures you don't have to create the load cases from scratch. There is no need to edit the load combinations on a new truss, just import them and make sure to edit the Special Loads if needed; all other settings automatically adjust to the new truss.
2. Click **OK** on the **Load Combination Editor** dialog to save your changes. **Do not** Cancel or you will lose your changes.
3. Run the truss and fix any errors, if needed.
4. Select any load combination (including the user combinations) in the **Applied Loads View** window to display the loads. For example, below is the first case created above, where you can clearly see the loads are applied as Up, Down, Right, Right for the two vertical loads and two shear loads, respectively:


![](/images/csdirector-cstruss/resources/images/ts-steeplefinalloading.jpg)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** A generic note displays on the TDD: **User-created load combinations exist on this truss**; this refers to the Loadcase report. The steeple dead loads will display at the locations entered, but the other loads will not:

![](/images/csdirector-cstruss/resources/images/ts-steepleloadstdd.jpg)

**Related Topics**