# Joint Details Report

**Purpose**

Displays plate orientation for each joint in relation to the center of the plate allowing for more accurate plate placement. You can select additional joints to include on the Properties pane. You can also adjust X and Y offset in Plate Monitor/Properties.

**Steps**

![](/images/csdirector-cstruss/resources/images/video-icon.png) Watch video

To generate a Joint Detail Report on a truss open in Truss Studio:

1. From the **Entry Mode** menu, select **Output** or click the Output button on the toolbar.
2. Navigate to **C:\SST\Client\RG_Files**.
3. Open the relevant Joint Detail Report.


The selected report displays.

A sample truss and associated report are shown below.

![](/images/csdirector-cstruss/resources/images/ts-sampletruss-jointdetailrpt-1281x523.png)

![](/images/csdirector-cstruss/resources/images/ts-jointdetail-report-overview.png)

1. Zoom in on a joint to review it in greater detail. This example focuses on the left heel joint.


For ease of reading the report, define grid lines. Set grid line parameters in **EnvData > Other > Draw Grid Lines in Joint Details Reports**.

![](/images/csdirector-cstruss/resources/images/ts-jointdetailreport-left-heel.png)

Information displayed for each joint includes:

- Joint number and scale of the drawing in the upper corners.
- Truss plate size & gauge (if anything other than 20-gauge)
- Truss member data (per member):


a. Joint-to-Joint numbers of the members.

b. Act: actual number of teeth in the member

c. Req: required number of teeth in the member

- X-offset from center of the joint if any.
- Y-offset from center of the joint if any.
- Teeth direction of truss plate on the joint (dark equals symbol).
- Angle of the plate relative to horizontal, with a positive angle for plates rotated counter-clockwise and a negative angle for plates rotated clockwise from normal.
- The Joint Stress Index (JSI) for this plate on this joint. The JSI quantifies the stress level of a plate contact area and all applicable design forces acting at the joint. JSI is the ratio of the applied force to the allowable design force and is used to determine if a joint is critical.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** Identical joints are consolidated into one grid box, showing one of the combined joints and all joint labels.

Two circles on the plate illustrate the following:

- Larger blue circle designates center of joint; this is typically the center of the scarf length of the members (depending on the joint type). The x and y offset lines orientation are indicated as part of the blue circle.
- Smaller black circle designates center of plate
- If there are no offsets, the center of the plate and center of joint are in the same location


Adjust X and Y Offsets

You can adjust offsets and see the changes reflected in the Joint Details Report.

In the report example shown above, there is an X offset of 1 and 14/16ths (distance between the center of the joint and the small circle, which is the center of the plate; parallel to line). There is a 1” offset in Y direction (perpendicular to line).

1. Highlight the left heel joint and open the **Properties** pane. The orientation of the plate on the joint is controlled by the [Move along](/csdirector-cstruss/help-center/design-view/plate-monitor/move-along) command, which displays in the Properties pane when a specific joint is selected. In this example, plate orientation is measured along the top chord.


![](/images/csdirector-cstruss/resources/images/ts-jointdetails-movealong-tc.png)

1. Edit the orientation of the plate on the joint using the **Move along** setting. You can select a different option in the drop down list or enter a specific angle. In this example, Bottom Chord alignment is selected. When you select this option, the x and y offsets change.


![](/images/csdirector-cstruss/resources/images/d-jointdetailmovealong.png) ![](/images/csdirector-cstruss/resources/images/ts-jointdetail-movealongchanged.png)

The X and Y offsets also change on the joint detail report.

![](/images/csdirector-cstruss/resources/images/ts-jointdetailreport.-xy-changed-582x430.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** See [Plate Offsets](/csdirector-cstruss/help-center/design-view/plating/plate-offsets) for more information.

**Related Topics**