# Gable Truss Design in Truss Studio

**Description**

A gable is defined as the portion of a wall that encloses the end of a pitched roof. In construction, the gable “wall” or gable “end” is formed by structural members, either as stick-framing, a structural building component, or a combination of both, depending on the project details.

A gable truss is a structural component in trussed roof systems used for this purpose. The gable truss typically has webs (or studs) spaced at 16 or 24 inches on center to support sheathing and is located to provide enclosure of a pitched roof. Gable trusses can also be used at interior locations to provide nailing for gypsum at ceiling transitions, or along demising walls to provide fastening for firestops in the attic space of commercial buildings and multi-family housing projects. For the scope of this topic, 4x2 ladder trusses, valley trusses, and piggy-back trusses are excluded from consideration.

A **non-structural gable** is continuously supported along the bottom chord and is sometimes called a common gable, consisting of structural studs at regular spacing.

![](/images/csdirector-cstruss/resources/images/cr-nonstructgable-927x534.png)

A **structural gable** truss is designed with structural webbing. It can be continuously supported along the bottom chord, partially supported, or can be a clear span design. This is common for transition gables or dutch hip roof styles, where a continuous wall does not provide bearing directly below the gable. Additional members may be added as ledgers to support tie-in trusses or to provide nailing in the field.

![](/images/csdirector-cstruss/resources/images/cr-structgable-951x552.png)

A **dropped gable** is a gable truss that has the top chord lowered (or “dropped”) to allow nominal framing (outlookers) to pass over the top chord and form the rake overhang of a structure. A dropped gable can be designed with a single structural top chord, or a stacked top chord, depending on the designer’s preference. When a full second chord is applied, it may be notched for rake overhang framing like a let-in gable. Examples of dropped gable truss designs are shown below.

![](/images/csdirector-cstruss/resources/images/cr-dropgable1-911x544.png)

![](/images/csdirector-cstruss/resources/images/cr-dropgable2-881x509.png)

![](/images/csdirector-cstruss/resources/images/cr-dropgable3-881x513.png)

![](/images/csdirector-cstruss/resources/images/cr-dropgable4-919x593.png)

A **let-in gable** is designed with a stacked top chord, where the bottom-most top chord is treated as structural and is trimmed to the web members of the gable truss. This allows for notching of the top chord in applications where there is no continuous support below the gable end.

![](/images/csdirector-cstruss/resources/images/cr-letingable1-880x485.png)

**Lay-in gables** are a non-typical type of gable. Lay-ins are used in place of field framing at the hip drop section to provide the required on-center support for sheathing only. Lay in gables are a non-structural component type.

![](/images/csdirector-cstruss/resources/images/cr-layingable-822x356.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** The trusses shown above are only examples of each truss type. Gable trusses may have a variety of geometry and options, which are not shown in the above trusses.

**Design Practices**

Truss Studio provides options to create each type of gable described above. The analysis of each type is different; therefore, it is critical as a designer to understand and use the proper options when designing for each type. It is also important to consider the TDD output for the desired use of the truss. Truss Studio automatically creates gable notes when certain functions are used to create gable end trusses. As a best practice, designers should review the TDD to ensure the appropriate notes are generated. These notes provide important additional information regarding bracing and truss analysis, which can indicate an error in the design methodology, depending on the note generated.

**Required Actions**

In Truss Studio, navigate to the Gable Dialog.

Each gable type can be created using different settings which are applied from the Specifications area. The settings labeled on the screen below correspond to the creation of each truss type.

![](/images/csdirector-cstruss/resources/images/cr-gabledialogcallouts-812x355.png)

1. When no additional settings are applied in the Specifications area, a non-structural gable is created with vertical studs only (all diagonal members removed).
2. When **Structural Gable** is selected, diagonal webs are left in place and vertical studs are infilled as “non-structural” members.
3. When **Lay-in Gable** is selected, the truss is not analyzed for forces. This setting is for hip-overlay framing only, to provide support for sheathing in that application.
4. When **Structural Gable** is selected, the **Let-in TC** option becomes available. When Let-in TC is selected, a stacked structural top chord is created and trimmed to fit against the structural webs in the existing design; this allows for notching of the top chord.
5. When **Drop TC** is selected, a non-structural stacked top chord is applied based on the settings to allow for notching of the top chord or placement of nominal outlooker framing.


For additional information regarding the fields in Gable Dialog, see [Gable settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/gable-settings). To learn more about creating a specific gable type, see [Create Gables](/csdirector-cstruss/help-center/design-view/create-gables/create-gables).

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** A Gable command must be used to produce rake overhang notes on the TDD. All gable trusses created using the Gable dialog will produce the following output in the Notes section of the TDD.

![](/images/csdirector-cstruss/resources/images/cr-gablewebnotetdd-759x132.png)

Keep this in mind when using DG (Dropped-Gable) or LG (Let-in Gable) commands in the TC profile line since those commands alone will not produce the required gable stud bracing or rake overhang notes. A workaround to apply the required notes without producing gable studs is to select a minimum gable stud length greater than the height of the truss. This way, no gable studs are produced, but the truss will generate correct output on the TDD.

![](/images/csdirector-cstruss/resources/images/cr-nostuds-1057x307.png)

A **Lay-in gable** design produces different output because it is not a true gable truss. There is no force or reaction summary produced on the TDD and the truss is noted as being used only *“for lay-in framing/bracing within a drop hip roof system…”*. The **Lay-in Gable** setting turns off analysis by Truss Studio for forces in this component, since it is for support of the sheathing only, and is not used as a typical load-supporting component in the system. No output is produced to describe the truss as a gable end, nor is there output to indicate an overhang in the truss design. Lay-in Gable is for use only in this application and not for common truss designs.

See the output on the TDD below for lay-in gable settings.

![](/images/csdirector-cstruss/resources/images/cr-layingablenotetdd-712x187.png)

**Related Topics**

[Create Gables](/csdirector-cstruss/help-center/design-view/create-gables/create-gables)