# Select a Connector Not in Inventory

**Purpose**

Use this feature to specify a connector not in your inventory

**Prerequisites**

A layout with truss-to-truss connections

**Steps**

1. On the **Truss Operations** menu, select **Manual Connector Selection** or click ![](/images/csdirector-cstruss/resources/images/ts-manualconnectorselection.png)on the Truss Operations toolbar.


The following prompt displays in the caption bar:

Select a connectivity indicator to create a connector. Esc or right-click to exit command.

1. Select a connectivity indicator.


The selected connection is highlighted, as are any other connections with the same girder and child trusses. The **Connection Details** window displays.

![](/images/csdirector-cstruss/resources/images/connection-details-306x167.jpg)

The color of the indicator may vary, depending on the status of the connection.

1. Select the desired options in the **Connection Details** window and click **OK**. There are several options that may display, depending on the analysis state of the trusses:


- If the trusses that make up the connection have not been analyzed (both the girder and child truss) the Analyze Trusses window displays. Click **Yes** to complete the analysis. If you select **No**, the connection indicators are deselected.


![](/images/csdirector-cstruss/resources/images/analyzefirst-275x144.png)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** The analysis honors the Transfer Loads Automatically setting (under Layout Settings > Load Transfer). If Transfer Loads Automatically is enabled, selected load transfer point loads are created on analysis. If this option is not enabled, the analysis runs without transferring loads. If load transfer point loads were previously transferred, the following window displays.

![](/images/csdirector-cstruss/resources/images/load-transfer-dialog-397x149.png)

- If the trusses were analyzed and are failing analysis, the Failing Analysis window displays.


![](/images/csdirector-cstruss/resources/images/notpassinganalysisdialog-323x122.png)

- If both the child and girder trusses have been previously analyzed and have passed analysis, Truss Studio generates a list of possible solutions. That list is filtered down to a list of solutions with only those connectors contained in the project inventory. This list displays on the My Inventory tab. If no solutions are available and contained in inventory, **No Solutions** is displayed.


![](/images/csdirector-cstruss/resources/images/my-inventory-431x258.png)

- The list can be further filtered by selecting one of the options in the Style drop down list.


![](/images/csdirector-cstruss/resources/images/my-inventory-solutions-with-style-dropdown-420x254.jpg)

- The Connections section reflects the selections made in the Connection Details window in step 1. The Connections section is not editable and is shown here only for informational purposes.
- Load, Uplift, and Plies are populated with the reaction information from the child truss.
- The Show Catalog Page and Add to Elevations buttons are disabled until one of the items in the list is selected. Once a connector is selected on the list and the Show Catalog Page button is selected, a PDF of the catalog page with the selected connector displays.
- If this window is re-opened after a hanger was specified, it will open to the tab where the connector was selected and the previously selected connector is highlighted.


1. When the **Connector Selection** window displays, select the **All Solutions** tab.


The **All Solutions** tab displays with all of the connectors that satisfy the load and profile requirements of the trusses that make up the connection. Note that this list is not dependent on inventory.

![](/images/csdirector-cstruss/resources/images/all-solutions-tab-connector-selection-395x242.png)

1. Select a connector that is not already in your inventory.


The selected connector is highlighted on the list and the **Show Catalog Page** and **Add to Elevation** buttons are enabled.

1. Click **Add to Elevation**.


The window closes and the selected connector is saved to **Miscellaneous items** in Director; it is marked as a **Special Order** item. It is also saved to the Elevation with the quantity of the number of connections that were highlighted in step 1 (the quantity of identical trusses that are being carried by the girder).

The hanger symbol is displayed on the layout. A hanger schedule is created if this is the first connector selected on the layout. If other connectors have been previously selected and the hanger schedule has already been created, the newly selected hanger is added to the hanger schedule.

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** The **Connection Info** tab displays the design parameters used in hanger selection, ensuring clarity and confidence in your hanger designs by making connector data more transparent. This text is informational only and cannot be edited, except by modifying the components that are being connected.

![](/images/csdirector-cstruss/resources/images/ts-connectioninfotab-877x534.png)

**Related Topics**

[Connector Selection Overview](/csdirector-cstruss/help-center/layout-view/connector-selection-overview/connector-selection-overview)

[Select Multi-truss Connectors](/csdirector-cstruss/help-center/layout-view/connector-selection-overview/select-multi-truss-connector)

[Select Connectors in Layout](/csdirector-cstruss/help-center/layout-view/connector-selection-overview/select-connectors-layout)