# Add and Modify Purlins

**Purpose**

Purlins are dimensional lumber that is fastened to the top or bottom chords of trusses connecting them together for bracing purposes, carrying sheathing, and transferring loading. Often used in "pole-barn" trusses where truss spacing is more than 2' on-center, and other conditions where sheathing is not directly attached to the truss chords. Purlins are applied perpendicular to the plane of the truss and are spaced at a maximum of 10'-0" o.c. per BCSI.

**Steps**

![](/images/csdirector-cstruss/resources/images/video-icon-38x39.png) Watch video - Improved purlin placement

1. Open a truss or layout.
2. From the Truss - Design view, click **Purlins**. From the Truss - Layout view, select **Purlin** from the **Truss Modifications** menu.


The **Purlin Zones** window displays.

If no new purlin zone entries were created, the default top and bottom chord entries are displayed; these are based on presets.

![](/images/csdirector-cstruss/resources/images/ts-purlinzone-dialog-callout-461x245.png)

1. Click **OK** to display the default purlin zones.


![](/images/csdirector-cstruss/resources/images/ts-purlinzonesdisplayed-625x210.png)

The purlins display on the truss.

**Add a Purlin Zone**

1. To add a new purlin zone, select **<<new entry>>**.
2. Define the purlin zone by completing the following fields.
3. Click **OK** to save your edits.


![](/images/csdirector-cstruss/transparent.gif)See example

![](/images/csdirector-cstruss/resources/images/ts-purlin-overviewgraphic.gif)

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:**To add multiple purlins without leaving the dialog box, click **Save** after each entry. Click **OK** to apply all entries to the current truss.

**Top/Bottom**- Specify whether to add to the top or the bottom purlin zone

**Start** - Specify the start point for the purlin zone

**End** - Specify the end point for the purlin zone

#### Spacing for purlins

Enter a user-defined o.c. spacing for the purlins to be applied to the truss. 10'-0" is the maximum that can be entered into this field.

**Hold spacing** - Maintains user-defined purlins at the specified spacing; supersedes any filler or system-generated purlin zone. If Hold Spacing is not selected and there is a filler in the same zone with its own purlins, the two zones are compared; whichever has the lowest purlin spacing takes precedence.

**Max Spacing @** - Truss Studio computes spacing based on the value entered in spacing field (minimum spacing) and value entered in Env Data > Analysis > Bracing Data maximum purlin spacing.

![](/images/csdirector-cstruss/transparent.gif)See an example

In the following truss, before the truss is run, the value entered for spacing is used for the purlins on the bottom chord:

![](/images/csdirector-cstruss/resources/images/ts-maxpurlinspacing-493x263.png)

If you select **Max Spacing @**, when the truss is run through analysis, the spacing may change:

![](/images/csdirector-cstruss/resources/images/ts-samplemaxpurlinspacing-499x174.gif)

**Modify a Purlin Zone**

1. To modify a purlin zone, select the purlin from the list displayed.
2. Make edits to the purlin settings and click **OK**.


![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:**To add multiple purlins without leaving the dialog box, click **Save** after each entry. Click **OK** to apply all entries to the current truss.

![](/images/csdirector-cstruss/resources/images/ts-selectpurlinedit-483x257.png)

The modified purlin displays.

**Delete a Purlin Zone**

1. To delete a purlin zone, select the purlin entry to delete.
2. Click **Delete**, then click **OK**.


The selected purlins are deleted.

![](/images/csdirector-cstruss/resources/images/note-onlinehelp.png) **Note:** The Purlins and Braces layer is turned off by default. See [Manage Layers](/csdirector-cstruss/help-center/layout-view/layers-management) for more information.

![](/images/csdirector-cstruss/transparent.gif)A warning note displays on-screen when MWFRS warning is used and purlins are not applied.

- MWFRS must be selected as the Wind Design Method; and
- Sheathing must be selected as the bracing method for any part of the top chord.  ![](/images/csdirector-cstruss/resources/images/ts-trussnotccwindloads-978x593.png)


**Related Topics**

[Bracing Data settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/bracing-data-settings)