# Display Control settings

Access these settings via **Env Data** > **User Interface** > **Display Control**.

See [OverHeight Line settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/user-interface-over-height-line-settings) and [Color Palette settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/color-palette-settings) for more Display Control settings.

**Field Descriptions**

| Setting | Description |
|  --- | --- |
| Display Additional Commands box on Truss Input | True displays the Additional Cmds input box; false hides it. |
| Display Additional Commands Step Controls | True allows you to review each Additional Command for errors. |
| Display member lengths -- Structural | True displays the structural members length; False does not. |
| Display member lengths -- Non-Structural | True displays non-structural members length; False does not. |
| Display member lengths -- min length | Set the Minimum length at which a member length will be visible. Minimum 03-00, maximum 83-03-00. |
| Display member lengths - Large Font | True displays members length in larger font; False displays standard text. |
| Display Louver Dimensions | True draws a dimension from the inside of the attic vent / louver to the end of the truss. When the size of the wall vertical webs are changed, the opening remains the same size, and the framing around the opening adjusts to the changed vertical web size. |
| Display Attic Room Location | True displays attic dimensions; false will not show dimensions. |
| Display Attic Living Space Loads | True displays attic living space loads; false will not show loads. |
| Display Cal Hip extension dimensions longer than | Enter a value for displaying Cal Hip extension dimensions. |
| Display Stub dimensions and labels | Toggle stub dimensions and labels for stubbed trusses on/off, as follows:  - When set to True, stubbed trusses display stub dimensions and stub labels - When set to True and Truss Studio is running in Director mode, Truss Studio sends Stub Left and Stub Right dimensions to CS Director. - When set to False, stubbed trusses will not display stub dimensions and stub labels - When set to False, trusses stubbed on the left-side will display running and first panel dimension start from the actual left-end of the truss, not the pre-stub location. - When set to False and Truss Studio is running in Director mode, Truss Studio will not send Stub Left and Stub Right dimensions to CS Director, resulting in 0-0-0 dimensions |
| Display top chord rake dimension | True displays top chord rake dimension and allows for printing on truss drawing. See Top Chord Rake Dimensions. |
| Dimension locations from left stub | False indicates that  left stub dimensions are included in cumulative dimensions; true excludes left stud dimensions from cumulative dimensions. When the setting is False, a note prints on the truss engineering drawing to indicate that some dimensions include the left stub dimension. |
| Dimension height to inside of peak | Display dimension from bottom chord to lowest point of top chord. |
| Include tail bearings in span dimension | When set to True, the overall span includes the tail bearing section, unless there is also a bearing at the heel; in that case, it is considered a supported overhang, not a tail bearing. The default for this setting is False. |
| Display bottom chord elevation ends dimension | When the elevations of the ends of the bottom chord in a roof truss are different Truss Studio must dimension the elevation difference. The dimension must measure the difference in elevation at the bottom of the far left and far right bottom chord ends.   - If the left end of the truss is stubbed, and the **Dimension locations from left stub** setting is True, this dimension measures from the stubbed, far left bottom chord end  - If the left end of the truss is stubbed, and the **Dimension locations from left stub** setting is False, this dimension measures from the original (pre-stub) far left bottom chord end  **Note:** A truss is stubbed if the Left Stub and/or Right Stub fields have a value greater than zero. |
| Include Ribbon Block notch dimensions | When True, Truss Studio draws additional dimensions for the ribbon pieces and notches.   ![](/images/csdirector-cstruss/resources/images/ts-autodimribbonnotches-580x314.png) |
| Display -- size of Selection Box for Joints | Size of joint selection box. Minimum is 01-00, maximum is 06-00. |
| Display truss members in layout | True displays trussed members in 3-dimensional views in the layout; False hides them. |
| Display nodes and analogs on drawing | True displays red analog lines and nodes upon analysis |
| Display Joint Data | True displays information about joints; False displays joints without any data.     ![](/images/csdirector-cstruss/resources/images/ts-jointtypedata-804x304.png)   ![](/images/csdirector-cstruss/resources/images/ts-jointtypedata-false-825x311.png)  See also [Plate Handling](/csdirector-cstruss/help-center/design-view/plate-handling/plate-handling-file-overview) |
| Display plates | True displays plates on joints; false displays joints without plates.   ![](/images/csdirector-cstruss/resources/images/ts-displayplates-true-826x311.png)     ![](/images/csdirector-cstruss/resources/images/ts-displayplates-false-848x319.png) |
| Display shear (red) and tension (green) and boundary (blue) lines on drawing | True displays colored lines on the truss drawing for shear, tension, and boundary. |
| Display voids | If set to True, voids are highlighted in layout and truss. Voids include floor chases or attic rooms. |
| Display obstructions | If set to True, obstructions drawn in layout display in Design view. |
| Display Wx2 vertical web indicator | If set to True, vertical webs are indicated on a floor truss. This feature gives designers the ability to locate chase openings at vertical members already located within design. |
| Display information on mouse hover delay (in seconds) | Number of seconds before member properties information displays when hovering mouse over truss piece.  Beginning with 2024.7 you can see the elevation of plane edges at overhangs and ridge lines when hovering mouse over those areas. If you hover the mouse over a flat plane, you will see a single elevation; when hovering over a sloping plane, you will see a high and low elevation.  ![](/images/csdirector-cstruss/resources/images/ts-wallelevationtooltip.png) ![](/images/csdirector-cstruss/resources/images/ts-lowhighelevationtooltip.png)  The mouse hover display is limited to plan view and is active only when in a selection mode; it is not active while in input and editing modes. |
| Pitch precision - # of decimal digits to display | Defaults to 2. All pitch indicators on-screen and on the output TDD will reflect the pitch rounded to the number of digits requested. |
| Don't display pitch less than #.#### | Defaults to 0.05.Any pitch less than the specified amount will be suppressed on-screen and on the TDD output. |
| Display Piece Labels | True displays piece labels on .RGT output. |
| Bold & optimize items on Wx2 truss report image for spans greater than | Generate improved Wx2 truss images in CS Director reports |
| Display object highlighting | When True, joints, truss plates, and dimensions are highlighted when hovering the cursor over those objects. |
| [OverHeight Line settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/user-interface-over-height-line-settings) |  |
| [Color Palette settings](/csdirector-cstruss/help-center/truss-studio-online-help/env-data-settings/color-palette-settings) | Color palette settings |
| Sealed Engineering Font Overrides | Define fonts for Sealed Engineering (TDD) Text |