# Walls and Planes settings

Access these settings via **Env Data** > **Layout Settings** > **Walls and Planes**. See Create Walls With Planes and [Create Walls with Veneer](/csdirector-cstruss/help-center/layout-view/create-walls-with-veneer) for more information.

**Field Descriptions**

**Setting**

Description

**Wall Orientation**

Define

wall orientation as left or right

**Wall Alignment**

Select Outside Edge, Inside Edge, or Center.

**Walls to be Exterior**

Define whether walls are interior or

exterior

**Walls are Load Bearing**

Define whether walls are Load bearing or Non load bearing

**Default wall width**

Define wall width

**Default top elevation of wall**

Define default top elevation

**Default bottom elevation of wall**

Define default bottom elevation

**Standard Heel Heights**

Define heel height size

**Custom Heel Height; set to '0' to use standard heel heights**

Define heel height or use 0 for standard heel height

**Heel height measured at outside of Fascia**

Define how heel height is measured

When multiple pitches are used on the same roof, adjustments must be made to the heel heights or overhang lengths to get the fascia to line up. The point for fascia alignment is the outside of the fascia and not the end of the truss overhang. This setting provides the ability to define the outside of the fascia and have the truss overhangs stop at the inside of the fascia. Note that this check box is only enabled if the Fascia Adjustment is not set to "None" and the overhang is less than or equal to the fascia thickness input in the Fascia Adj drop down list.

**Cant dimension**

Define default cantilever dimension. **None** should be used only on interior walls with no planes attached. Exterior walls with planes must have a cant and overhang attached to them; use the 00-00 setting for exterior walls with planes.

**Overhang Length**

Default value for a wall to have a specified overhang length. **None** should be used only on interior walls with no planes attached. Exterior walls with planes must have a cant and overhang attached to them; use the 00-00 setting for exterior walls with planes.

**OH: How measured?**

Dimension for overhangs:

- OutPnt for farthest top chord point
- InPnt for the farthest inside point of the top chord
- Rake for the rake


**OH: End Cut**

Set overhang end cut as follows:

- Plumb
- Square
- Angle
- Seat (previously DblCut)
- Fascia


Note: When a left and/or right overhang on a rafter is set to zero (0) this setting is not applied to that end of the rafter and a Plumb cut is used instead. This setting is applied on any overhang value of 1/16 or higher.

**OH: Angle 1**

Define overhang for first angle

**OH: Angle 2**

Define overhang for second angle

**OH: Length of Seat or Fascia Cut**

Define length of seat cut or fascia cut

**Fascia Adjustment; set to '0' for None**

Adjust fascia or use 0 for none

**Attach Roof Plane to wall**

Auto-attach a roof plane to a wall if set to True

**Attach Ceil Plane to wall**

Auto-attach a ceiling plane to a wall if set to True

**Attach Roof Plane to work line**

Auto-attach roof plane to workline if set to True

**Attach Ceil Plan to work line**

Auto-attach ceiling plane to workline if set to True

**Roof pitch from wall**

Define roof pitch for a wall

**Ceiling pitch from wall**

Define ceiling pitch for a wall

**Roof pitch from work line**

Define roof pitch for a workline

**Ceiling pitch from work line**

Define ceiling pitch for a workline

**Hip Drop Dim for flat TC segments**

Define hip drop for flat top chord

**Wall veneer**

Enable veneer for a wall

**Beam veneer**

Enable veneer for a beam

**Default veneer width**

Define default width of veneer

**Gap between wall and veneer**

Define gap distance between the wall and the veneer

**Veneer is load bearing**

Specify whether veneer is load bearing

**Veneer to match wall elevation**

When set to True, veneer will be created at the same top and bottom elevation as the wall.

**Default top elevation of veneer**

Define the top elevation of the veneer; this does not have to be the same elevation as the top of the wall.

**Default bottom elevation of veneer**

Define the bottom elevation of the veneer; this does not have to be the same elevation as the top of the wall.

**Defining edge is the veneer**

When enabled, the distance input in the Layout Commands text box on the Settings dialog defines the length of the wall to the outside of the veneer and not to the outside of the wall.

**Plane Indicators**

**Plane tag size, or 0 to disable**

Specify size of the plane tag

**Display pitch in tag**

Display the pitch in the plane tag

**Circle walls - min wall length**

Minimum length of arc wall

**Wall Colors by Elevation**

**Wall Data**

Display available data for a wall

**Walls are colored by elevation**

When set to True, define colors for walls based on elevation.

**Bolds Inside line of load bearing walls**

When set to True, the inside line of load bearing walls displays in bold.

**Truss Colors by Type**

Define/edit these colors using the Color Settings dialog. Settings are not editable in EnvData. See

[Define Truss Type Colors.](/csdirector-cstruss/help-center/layout-view/define-truss-type-colors)

**Girder**

Girder color

**Gable**

Gable color

**Hip Girder**

Hip Girder color

**Secondary Hip Girder**

Secondary Hip Girder color

**Jack**

Jack color

**Corner Girder Truss**

Corner Girder Truss color

**Corner Rafter**

Corner Rafter color

**Stacked Corner Rafter**

Stacked Corner Rafter color

**Rafter**

Rafter color

**Stacked Rafter**

Stacked Rafter color

**Valley Truss**

Valley Truss color

**Layin Gable**

Laying Gable color

**Shear Panel**

Shear Panel color

**Color Trusses by Type**

When set to True, define colors for walls based on elevation.